JournalArticle SearchList By TopicSubmit ArticleRegister
ResourcesWhite PapersGlossaryStock TrackerPresentations
2 Nov 2004 |
Inkjet Printing Electronics
One of the ultimate goals in electronics is the ability to directly write electronic components and circuits. Advancing materials chemistry and developing printhead technology is bringing this goal closer to reality. However, requiring the integration and optimisation of many factors from print fluid formulation to printhead design and print platform engineering to process design there remains some way to go.
Patterning Technologies Limited , a technology integrator who brings together these elements and provides industrial scale solutions, provides an industry update.
Drop on demand printing
Drop on demand printing (inkjet printing applied to industrial processes) utilises the piezo electric effect to deliver precise and consistent quantities of fluids. Typically, current printheads are designed with 100 plus nozzles on a single printhead. Each nozzle is able to independently deliver 30 pico-litres of fluid at a frequency of up to 20,000 drops per second (20 KHz). Such a printhead would have a natural resolution of the order of 50 dpi and therefore grouped in an offset bank of 8 heads can generate a 400dpi resolution. Multiple print passes allow higher resolutions.
Printing onto absorbent surfaces such as paper, where the substrate acts as a brake to fluid flow is relatively straightforward and sustains the resolution. However, fixing the image on less friendly surfaces is an important factor in achieving the desired end product. The core of Patterning Technologies Ltd's know-how resides in this area and it has successfully demonstrated its capability to achieve industrial scale applications.
What does this mean in practical terms? Although dependent on the print fluid and print surface characteristics, the above design at 400 dpi resolution would enable feature sizes in the region of 100 micron track and gap, without further post printing treatment. The printing time for a 600mm x 800mm substrate would be of the order of 1 minute.
Digital inkjet printing is a binary process. The image to be printed is broken down in to a matrix of squares with an on-off print signal to the nozzle. Therefore printing diagonal lines at low resolution can suffer the potential of a saw tooth effect which is seen as a challenge for some applications. Introduction of 'grey scale' in the soon to be released new generation printhead (a process where the printer fills in the saw tooth steps by addressing 1600dpi) reduces this problem significantly.
In addition to 'greyscale' these new printheads will deliver smaller drop volumes allowing smaller feature sizes that are expected to be in the region of 50 micron track and gap. Although this may not be the limit of printhead design, it does mean that without post print treatment these feature sizes limit the direct write capability. For example, in the displays sector screen sizes of 40 inches and above.
Finer feature definition either requires pre-treatment of the substrate surface to influence the flow of material on contact with the surface or post print ablation with laser or other techniques. There are ongoing novel technological developments in all these areas.
Finally, having fixed the image on the surface, it is crucial to be able to control the pattern with a reliable and consistent delivery system. This is the domain of the print platform and the integration of mechanical design with software programming. Ink companies therefore tend to work closely with machine manufacturers such as Xaar, Xennia and Spectra to bring fluid and printhead technology together. with the total manufacturing process to produce an industrial scale integrated solution.
Print Fluid Formulation
Print fluids can be 100% solids or suspensions provided the particle size is within the printhead capability. Many iterations are generally required to produce a fluid that has the;
- correct performance characteristics to 'jet' from the printhead
- interacts with the substrate to create wetting in the desired manner and
- withstands the final processing and performance conditions for which they are destined
The process requires active co-operation of all involved
With fluid supplier partners PTL has formulated a range of fluids for a number of applications. It has a tried and tested formulation for etch resist, hardcoating, legend printing and carbon. The etch resist has been some 5-6 years in development and has been successfully demonstrated in photo-chemical etch process applications for a number of clients. It is equally relevant to the electronics and displays industry, where direct writing of the patterned etchmask eliminates costly steps in the photolithography process. This is a pre-cursor of course to the ability to directly write the patterned end product.
PTL is also developing transparent conductors and metallic silver and gold. PTL has achieved 200 ohms/sq with transparencies of 75% and has demonstrated direct write patterning of the transparent conductor. With one development client a working display device using its printed conductor has been produced. PTL has plans to develop this work further including printing on plastic substrates and laser annealing.
Following closely behind the transparent conductor is development in printing of metallic conductors. A key advantage of drop on demand printing over other processes is the access it provides to higher performance and usually higher cost materials may be used effectively. Because the fluid is deposited only where it is required, drop on demand means little or no waste and higher value materials become economically viable. PTL has achieved feature sizes of 100 micron and conductivities of 50% and 75% of the bulk properties for silver and gold respectively. Post print metallization is still required and at present temperatures of 400 deg C are required and development work with the formulator to bring this down to 150 deg C is targeted.
PTL's intellectual property includes patents covering the printing of passive and active devices such as resistors, capacitors and transistors. Applications for Government grants for the development of this technology is in hand and commercial processes are in place to work with its formulators to develop inorganic active components. PTL believes the short to medium term will be driven by the higher performance of inorganic materials. There is clearly a future for organic devices and there is a lot of active research and development in this area. However, PTL considers that this will be over a longer time horizon.
As part of its ongoing development plans, PTL is also investigating new and interesting formulations applicable both within and outside of the electronics and displays arena. PDP and LCD still compete for a place in the market, but print technology is applicable to both. In addition to the direct writing of devices, inkjet printing is seen to offer lower cost and operationally more flexible solutions to printing alignment layers, conductors and colour filters. In the case of PDP, inkjet printing's ability to create 3D micro-structures has its use in printing of the wells in addition and also the phosphors.
Process Integration - the real benefits:
The consequences of inkjet printing are significant in so far that the traditional photo-lithographical processes are turned on their head and simplified.
Direct write patterning of etch resist removes the need for photo-tools, expensive coating, exposure and develop/wash process equipment.
PTL can directly write patterned transparent conductors and is now refining the performance through further development work. With direct write etch and strip are also removed.
As data are digitally stored there is the added operational flexibility of being able to make last minute changes, process multiple jobs and of particular interest to the displays industry, with camera detection the ability to re-work jobs in-line increasing yields.
The capital cost of inkjet printers is significantly less than the photolithographical equipment that they replace. Given also the reduced space requirements inkjet printing technology has the added benefit of reducing clean room areas and hence facility costs. There also environmental benefits by reducing or even removing the need for waste treatment facilities. This makes a very compelling economic case for inkjet printing technology and an extremely attractive alternative to the billions of dollars that are required to generate the economies of scale using traditional processes.
Significant progress has been made in the field of inkjet technology to develop processes that can
- Reduce capital invest
- Reduce operating costs
- Speed up processing times and
- Increase operational flexibility
Many opportunities remain for the technology as material chemistry develops and the mechanical designs of printheads and print platforms evolve further. Optoelectronic technology dependent on multi-stage processes to build transitors and other components will be decimated by the ability to print these directly. The experience of developments thus far means the pace of progress is accelerating and with such a massive prize for success the momentum exists. Direct writing of components is already within the grasp of many and PTL expect to see this developing in months rather than years.
For more information, PTL will be presenting at Printed Electronics 2004 , New Orleans, 6-8 December 2004.
RFID Forecasts, Players and Opportunities 2014-2024
Financing for invisible energy harvesting coatings
Excitons observed in action for the first time
Smartphone battery fully charges in thirty seconds
The automotive sector strengthens adoption of supercapacitors
US Navy sends Bluefin Robotics' AUV in search of Malaysian airliner
Danish company produces high-tech lightweight-chassis